Make A Solar Battery Charger



Solar Garden Light Hack - Battery Charger

Dollar Store Solar Path Light Hack

Here is a simple solar garden light hack. Get four cheap dollar store path lights for this project. Using the original garden light parts, you can make a high speed solar battery charger for AA or AAA batteries. Depending on which model you get (you normally cannot tell from the outside) you will either have AA or AAA batteries and sockets inside the solar path light.



Solar Garden Light Hack - Make Battery Charger

Take apart your solar garden lights. Twist the stem and globe off of the solar cell by giving it a little twist. The solar cell and circuitry pops right off. Use a screw driver and open up the bottom of the unit. Then carefully break off the wires connecting the solar cell to the circuit board. Be careful not to break the wires connecting to the solar cell itself. Then you can remove the screw that holds the little circuit board in place. Cut the wires in half to remove the circuitry from the battery charging socket.

Repeat this process for all four solar path lights. You want to have four solar cells and two battery sockets.



Homemade solar battery charger from dollar store path lights

Find a piece of plywood or other wood to use for the back of your solar charging unit. Refer to the photo below. Line up your solar cells to see how they will fit on the board. Then, using the original bottom part of the unit, mark through the holes in the bottom so you can drill holes into the wood in order to mount your solar cells to the board. Watch the video (bottom of this page) for more details on how this was done.

Find some small screws that will be long enough to pass through your board and into the solar cells. Drill holes in your board as marked. Make the holes just larger in diameter than your screws so they can pass through the board.

Screw the solar panels onto the board. See the photo below right.



Mark holes for your solar charger cells    Mounting the solar cells for your charger



Next mount your two battery sockets to the board as well. For the next step you will need some fine insulated wire. Two colors would be preferred. Also get a diode. Any sort of blocking diode or rectifier diode will do. Its only purpose will be to limit the charging current in only one direction to prevent the batteries from discharging back through the solar cells. If a cloud passes over, the batteries can discharge back through the solar cells without a diode. A diode is like a one way switch.

Place the diode in the circuit as shown in the schematic below. Notice the silver colored bar on the bottom. It is important to install the diode in the exact same way.

Attach a piece of wire between every negative lead of the solar cells. Connect them all together in parallel. This means that they will simply all be connected together. Then run a wire form the negative leads of the solar cells to each of the negative ends of the battery sockets.



Homemade solar battery charger schematic diagram
Solar Battery Charger Schematic Diagram
(Click for larger. Opens new window.)

Do the same for all of the positive leads. Make sure you connect the diode between the positive output of the solar cells and the battery sockets. Now solder all of your wires together. (Notice that in the video, the soldering iron is being run off solar energy. Totally green.).



Mount the solar battery charger sockets    Solder your solar charger wires together

Take a volt meter and make sure that your solar cells are putting out enough voltage in the sun. You should get about 3 volts or so. Anything above 2.5 is fine. Also make sure that your wires are connected correctly to the plus and minus of the battery sockets.

Add a pair of batteries that need to be charged up and check with a volt meter. You should immediately see the voltage drop to the level of the batteries, then start to rise again rapidly. The voltage will rise a bit and then level off as the batteries start to take a charge. At about 1.5 to 1.6 volts (depends on your batteries) you can remove them. They are charged.

Dollar store path light hack

You may want to add a small volt meter to your solar charger as well so you can always see the state of charge of your batteries.

See the video here:



Feel free to ask any questions or get help with your project on our Support Forum.

Related Articles


How To Wire A Homemade Generator

Windmill And Generator Wiring And Design
Convert A Table Fan Into A Wind Generator

How To Make A Windmill From A Fan Motor
 

Get Your Project On The DIY World Pages

Upload your project ideas to The Do It Yourself World pages. Now you can write your own DIY articles on the Do It Yourself World Article Pages. Please Click Here to get started.


Subscribe


Enter your email to receive updates about new projects.


Donate

The DIY World invests time and money into every project. Help us keep posting valuable experiments.


Related Articles


How To Wire A Homemade Generator

Windmill And Generator Wiring And Design


How To Make Your Own Solar Panels For $1 Per Watt

The Do It Yourself Solar Panel Book. How to make your own solar panels.



$1 Solar Panels

Make your own solar panels for $1 per watt
Get the book

The Complete DIY Solar Panel Book


Non GMO Heirloom survival seed vaults

Wise Survival Food Storage and Foods