Make A Fireplace Boiler Heating System

Affordable, simple wood stove radiator heating system for camper, RV or mobile home.

Homemade woodstove boiler heater system
Antique Wood Stove Water Boiler System

Step by step instructions how to make your own wood stove boiler / radiator heating system.

A fireplace is a great thing to have, especially if you are living off the grid. But a fireplace is limited to heating only the room that it is installed in. Most of the heat from a fireplace goes out the chimney, to heat the outdoors. One way to improve your home heating is to install a Homemade wood stove heat exchanger on the chimney pipe to capture some of that lost heat.

But another way to heat your home better is to make a wood stove boiler heating system. A homemade boiler heater can be installed in your house, RV, camper or trailer home. It will allow you to pump heat into the rooms farthest from the wood stove. And it does not need to be expensive either. The example shown here was under $100, and that is if we had purchased all the parts new, instead of recycling.

The diagram below shows the system that we built. The only difference was that our antique wood stove has a built in water boiler. The heater system parts include a heat exchanger on the fireplace itself to heat up water in the pipes. Then water tubes bring the hot water to a radiator. A water pump circulates the water through the system. Then a fan blows heat through ducts in your home. A hot water expansion tank is necessary to prevent the build up of high pressure in the system. Also a water drain valve has been added for maintenance. Also necessary is a pressure relief valve. This releases water pressure in case of a failure of the expansion tank. You can hold your mouse over the photo for a larger view.

DIY radiator home heating systemHomemade boiler heating system diagram
Diagram of a fireplace boiler heater system


Heating a home that already had a forced air, or central air heating system is even easier and cheaper. Most trailer homes, RVs and campers have ductwork installed for a forced air heating system. Most of these trailers have a propane heater that blows heated air through the trailer. You can use the heating ducts already in place for your new heating system.



How to make the wood stove boiler



Part 1 - Make the radiator and blower box

Please refer to the images below for the next steps. First, you need to get a car heater core. This is just like a radiator, only smaller. If you are working in a normal house, then you can get foot board radiators from a plumbing and heating supply shop for a fair price. If you are installing the heater in a camper, RV or mobile home, then a car heater core will be the best due to size restrictions of the original heating system. If you will be using household radiators, then skip down to the plumbing part of this article. A car heater core can be found used at a junk yard, or at your local auto shop for as low as $20 new. This one was free from asking around, brand new.

Make a box that perfectly fits your car heater core. The box should fit snugly, but without forcing the heater core into it. You want to protect it from damage. In the second photo below you can see the box taking shape and in the third photo you see the heater core sitting in the box frame.

In the fourth photo below you can see that the original trailer ductwork framing was mounted to the new radiator box. Your original trailer ducts are usually mounted on a metal box with round cutouts all around. The flexible ducts are attached with a hose clamp to metal lips on the box. These metal lips can usually be removed. The box is a universal fit box and made for multiple models of trailer. Remove the metal duct mounts and attach them to your new homemade heater core box.

There is only room for two ducts, but you may need more. A "T" connector may be needed to branch off the heat to more rooms, if needed.

Making a boiler heating boxHomemade fireplace boiler heater box
Begin making the radiator box
Begin making the radiator boxStart building the heat exchanger box
Make the radiator blower box

Placing the radiator in the blower boxFit the heater core in the box
Fitting the heater core in the blower box
Attach heater blower ductsMount the ductwork to your heater blower
Attach ductwork to heater blower box

Find yourself a decent sized fan for the project. This will be your new heater blower fan. For our project, using a fully off grid system, we used a 12 volt computer server fan. It blows a ton of air and uses very little power. For a house on normal power, then find a suitable blower for the job.

Set the heater core safely aside, away from the work space. Now cut a thin sheet of plywood to fit the other side of your new homemade radiator box. Then use a jig saw or hole saw to cut a hole out to fit the blower fan. Notice in the photo below the use of a battery powered jig saw in our off grid contruction. In the second and third photos you can see the new blower fan being mounted onto the heater box.

Place the fan on the plywood sheet and use an ink pen or nail to mark the fan mounting holes in the blower box. Drill out the fan mounting holes in the heater box cover. Then find nuts and bolts that will fit through both the fan housing and the lid of the blower box. Attach the fan securely to the housing.

After both the heating ducts and the blower fan are assembled, then you can place the heater core inside the heater blower box. Make sure everything fits together nicely. If it is all ok, then you can assembly the heater blower box and radiator.

In the last photo, you can see that the new heater blower box is now finished.

Prepare to install heater blower fan motorInstalling heater fan blower motor
Cut hole for heater blower fan
Install fan motor to heater blower boxMount DIY heater blower to radiator
Mount Heater Blower Fan To Box

Homemade hot water heating system blowerHomemade heater blower unit
Fan Installed On Heater Blower Box
Homemade heater blower unit is finishedDIY heater blower unit is assembled
Completed Heater Blower & Radiator Box

This completes part one of the homemade hot water heating system for your home. Click DIY home boiler heating system Pt 2 for more...

Feel free to ask any questions or get help with your project on our Support Forum.

Note: Working with fire can be dangerous. Please use extreme caution when working with open flames. Extreme pressure can build up in a boiler system. Be sure to install a professional pressure release system to prevent explosion. Do NOT set this system up without an expansion tank.



 

Get Your Project On The DIY World Pages

Upload your project ideas to The Do It Yourself World pages. Now you can write your own DIY articles on the Do It Yourself World Article Pages. Please Click Here to get started.


Subscribe


Enter your email to receive updates about new projects.


Donate

The DIY World invests time and money into every project. Help us keep posting valuable experiments.




$1 Solar Panels

Make your own solar panels for $1 per watt
Get the book

The Complete DIY Solar Panel Book


Non GMO Heirloom survival seed vaults

Wise Survival Food Storage and Foods